Houston Concrete Slabs
New Pours, Harris County TX
Class C motorhome parked on a concrete pad beside a house
RV and Boat Pads

RV and Boat Pads in Houston, TX

An RV pad in Houston, TX is a long concrete slab, usually 12 to 14 feet wide, built thick enough for a motorhome's axles and leveling jacks and sloped to shed Gulf Coast rain. Houston Concrete Slabs pours RV pads and boat pads for travel trailers, fifth wheels, bay boats and the trucks that pull them.

  • Motorhomes and fifth wheels
  • Bay boats on trailers
  • Thicker where axles sit
  • Drains off, not toward the house
Get a Free Quote

Sizing an RV pad in Houston

Start with the rig, not the yard. Length decides most of the price, but width is what people get wrong: a motorhome with its slides out and its door open needs more room than its road width. Most RV pads end up 12 to 14 feet wide. Leave room at the front for the hitch or tow car and at the back for whatever hangs off the bumper.

RV and boat pad sizes and cost (computed)
Pad forExample sizeAt $6 to $14 per sq ft
Bay boat on trailer10x28 (280 sq ft)$1,680 to $3,920
Travel trailer12x36 (432 sq ft)$2,592 to $6,048
Class C motorhome12x40 (480 sq ft)$2,880 to $6,720
Fifth wheel with truck14x50 (700 sq ft)$4,200 to $9,800
Class A motorhome14x50 (700 sq ft)$4,200 to $9,800

Rate: constructlytools.com Houston guide, driveway $6 to $14 per sq ft installed, May 16, 2026. Sizes are examples; measure your own rig with slides out.

Motorhome parked on a paved lot under palm trees
A motorhome parked on pavement.

Thickness and steel for axle loads

A motorhome doesn't spread its weight evenly. It sits on a few tire patches and, once parked, on leveling jacks with small feet. MBMI's steel building guide gives 4 to 6 inches as typical slab thickness and 6 to 8 inches where heavy equipment sits; an RV pad belongs toward the heavier end, at least where the wheels and jacks land. Rebar rather than light mesh is the usual choice for vehicle loads on clay. The thickness, rebar and vapor barrier guide explains the trade-offs.

The approach

The pad has to meet the driveway or the street without a hump that drags a hitch or a trailer tongue. Where it crosses a drainage ditch, the culvert and its cover need sizing too. Work in the City right-of-way, such as a new curb cut, isn't the same as work on your lot; see the Houston slab permit guide.

Boat pads: rinse water and the bay

From Houston the water is a tow away, whether that is Galveston Bay down I-45, Lake Conroe or Lake Livingston, and a trip usually ends with the hull and motor rinsed on the pad. A boat pad should fall toward the street or a yard drain, away from the house and the garage, with a broom finish that stays grippy when wet. Size it for the trailer and tongue jack, plus walking room on both sides.

Blue boat on a trailer parked at the edge of a lot
A boat on its trailer. The pad has to fit the trailer and the tongue, not just the hull.

Drainage on Houston clay

A 500 sq ft pad sheds a lot of water in a Houston downpour, and Bush Intercontinental averages 51.84 inches of rain a year (NOAA 1991 to 2020 normals). On slow-draining Beaumont clay that water needs somewhere to go. The base is built up and compacted, the pad is sloped along its length, and the downhill edge is planned so water doesn't undercut the slab or pond against a fence.

For an RV or boat pad quote

  • Length and width of the RV or boat trailer, with slides out
  • Whether the tow vehicle parks on the pad too
  • Where it connects: driveway, street or gravel drive
  • Any ditch, culvert or gate along the route
  • HOA or deed rules about parking an RV or boat

More on pricing: the Houston slab cost page.

Request a Free Quote

It takes about a minute. The quote is free.

Get an RV or boat pad quote

Send the rig or boat length, the pad location and the address. The quote is free.

  • A free quote with nothing to sign
  • New pours only: slabs, pads, footings
  • Houston, Harris County and nearby communities
  • Name, phone, address and the job
Request a Free Quote

It takes about a minute. The quote is free.

RV and Boat Pads in Houston: Questions

Blue boat on a trailer parked at the edge of a lot
A boat on its trailer. The pad has to fit the trailer and the tongue, not just the hull.
How much does a concrete RV pad cost in Houston?

Driveway pricing fits best: constructlytools' Houston guide (May 2026) lists driveways at $6 to $14 per square foot installed. A 12x40 RV pad works out to $2,880 to $6,720 at that rate.

How big should an RV pad be?

The rig's length plus room for the tow vehicle or a walkway, and wide enough to open the doors and run out the slides: commonly 12 to 14 feet wide. Measure the RV with slides out before settling on a width.

How thick should an RV pad be?

Thicker than a patio. MBMI's steel building guide treats 4 to 6 inches as typical and 6 to 8 inches as the range for heavy equipment; a loaded motorhome's axles and leveling jacks put concentrated loads on small spots, so the thicker end makes sense.

Do I need a permit for an RV pad in Houston?

A plain pad is flatwork, which the City's code exempts when it isn't covered by the Infrastructure Design Manual and stays within the impervious-area limit. A cover or carport over it is a structure and is treated separately.

Should a boat pad be different from an RV pad?

Mostly in size and drainage. A boat pad has to fit the trailer and tongue, and it gets rinse water after every saltwater trip, so it should drain off the slab rather than toward the house.

Parking an RV or boat at home?

Send the length and the address for a free pad quote.

Get a Free Quote
Free Quote